HOME  |  MAP  | CONTACT |  PRODUCTS

HOME  |  MAP  | CONTACT |  PRODUCTS

这是描述信息
1

1

2

2

3

3

4

4

Four steps need not worry about laser cutting machine

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2020-01-20 09:29
  • Views:

(Summary description)The so-called laser cutting machine depends on the laser. If the metal laser cutting machine encounters the situation that the equipment does not emit light in the use process, it is quite a headache. But you don't have to worry too much. In case of this kind of failure, the first thing to do is to check the laser cutting machine equipment by yourself. You can follow the following four steps: Do four steps without worrying about laser cutting machine light: 1. Check whether the water circulates normally and make the water circulates normally. If the water protection is broken, short circuit the water protection for use; 2. If there is no light, the power supply may fail and it needs to be replaced. Pre adjust the point to see if the ammeter swings. If not, use the multimeter to check whether the laser power supply has 220V power supply, 3. If the light comes out, the potentiometer is broken and needs to be replaced. You can also test whether the water protection is broken by GND ground wire and P water protection nipple on the power supply, and check the maximum output power by shorting + 5V and ain, 4. If yes, the card is normal. There is no possibility that the signal of the card is faulty. If the program doesn't work out, the connecting card can use a multimeter to measure whether there is more than 3V DC voltage between 15h or 16L angle and 14 angle

Four steps need not worry about laser cutting machine

(Summary description)The so-called laser cutting machine depends on the laser. If the metal laser cutting machine encounters the situation that the equipment does not emit light in the use process, it is quite a headache. But you don't have to worry too much. In case of this kind of failure, the first thing to do is to check the laser cutting machine equipment by yourself. You can follow the following four steps:

Do four steps without worrying about laser cutting machine light:



1. Check whether the water circulates normally and make the water circulates normally. If the water protection is broken, short circuit the water protection for use;



2. If there is no light, the power supply may fail and it needs to be replaced. Pre adjust the point to see if the ammeter swings. If not, use the multimeter to check whether the laser power supply has 220V power supply,



3. If the light comes out, the potentiometer is broken and needs to be replaced. You can also test whether the water protection is broken by GND ground wire and P water protection nipple on the power supply, and check the maximum output power by shorting + 5V and ain,



4. If yes, the card is normal. There is no possibility that the signal of the card is faulty. If the program doesn't work out, the connecting card can use a multimeter to measure whether there is more than 3V DC voltage between 15h or 16L angle and 14 angle

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2020-01-20 09:29
  • Views:
Information
The so-called laser cutting machine depends on the laser. If the metal laser cutting machine encounters the situation that the equipment does not emit light in the use process, it is quite a headache. But you don't have to worry too much. In case of this kind of failure, the first thing to do is to check the laser cutting machine equipment by yourself. You can follow the following four steps:
 
Do four steps without worrying about laser cutting machine light:
 
 
 
1. Check whether the water circulates normally and make the water circulates normally. If the water protection is broken, short circuit the water protection for use;
 
 
 
2. If there is no light, the power supply may fail and it needs to be replaced. Pre adjust the point to see if the ammeter swings. If not, use the multimeter to check whether the laser power supply has 220V power supply,
 
 
 
3. If the light comes out, the potentiometer is broken and needs to be replaced. You can also test whether the water protection is broken by GND ground wire and P water protection nipple on the power supply, and check the maximum output power by shorting + 5V and ain,
 
 
 
4. If yes, the card is normal. There is no possibility that the signal of the card is faulty. If the program doesn't work out, the connecting card can use a multimeter to measure whether there is more than 3V DC voltage between 15h or 16L angle and 14 angle

Scan the QR code to read on your phone

Copyright: Dalian kaitailong Equipment Co., Ltd   Powerby:300.cn  dalian  辽ICP备09027612号-1